Wi-Fi Technical Information

Evolution of Wi-Fi standards

The IEEE standard that governs Wi-Fi technology is IEEE 802.11; that standard has gone through several generations since its inception in 1997.

802.11. The original version of the standard, released in 1997, specifies two raw data rates of 1 and 2 megabits per second (Mbit/s) to be transmitted via infrared (IR) signals or by either frequency hopping or direct-sequence spread spectrum in the Industrial Scientific Medical frequency band at 2.4 GHz. IR remains a part of the standard but has no actual implementations.

802.11a. The 802.11a amendment to the original standard was ratified in 1999. The 802.11a standard uses the same core protocol as the original standard and yields realistic throughput in the mid-20 Mbit/s. Since the 2.4 GHz band is heavily used, using the 5 GHz band gives 802.11a the advantage of less interference. However, this high carrier frequency also brings disadvantages. It restricts the use of 802.11a to almost line of sight, necessitating the use of more access points.

802.11b. The 802.11b amendment to the original standard was ratified in 1999. 802.11b has a maximum raw data rate of 11 Mbit/s and uses the same CSMA/CA media access method defined in the original standard. The dramatic increase in throughput of 802.11b (compared to the original standard) along with substantial price reductions led to the rapid acceptance of 802.11b as the definitive wireless LAN technology.

802.11g. In June 2003, a third standard was ratified: 802.11g. This works in the 2.4 GHz band (like 802.11b) but operates at a maximum raw data rate of 54 Mbit/s, or about 24.7 Mbit/s net throughputs (like 802.11a). Despite its major acceptance, 802.11g suffers from the same interference as 802.11b in the already crowded 2.4 GHz range. Devices operating in this range include microwave ovens, Bluetooth devices, and cordless telephones.

802.11n. 802.11n builds upon previous standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput through spatial multiplexing and increased range by exploiting the spatial diversity, through coding. On January 19, 2007, the IEEE 802.11 Working Group unanimously approved 802.11n to issue a new Draft 2.0 of the proposed standard.


Wi-Fi: How it Works

Wi-Fi networks use radio technologies called IEEE 802.11 to provide secure, reliable, fast wireless connectivity. A typical Wi-Fi setup contains one or more Access Points (APs) and one or more clients. An AP broadcasts its SSID (Service Set Identifier, "Network name") via packets that are called beacons, which are usually broadcast every 100 ms. The beacons are transmitted at 1 Mbit/s, and are of relatively short duration and therefore do not have a significant effect on performance. Since 1 Mbit/s is the lowest rate of Wi-Fi it assures that the client that receives the beacon can communicate at at least 1 Mbit/s. Based on the settings (e.g. the SSID), the client may decide whether to connect to an AP. If two APs of the same SSID are in range of the client, the client firmware might use signal strength to decide with which of the two APs to make a connection.

The Wi-Fi standard leaves connection criteria and roaming totally open to the client. This is a strength of Wi-Fi, but also means that one wireless adapter may perform substantially better than another. Since Wi-Fi transmits in the air, it has the same properties as a non-switched wired Ethernet network, and therefore collisions can occur. Unlike a wired Ethernet, and like most packet radios, Wi-Fi cannot do collision detection, and instead uses an acknowledgment packet for every data packet sent. If no acknowledgement is received within a certain time a retransmission occurs. Also, a medium reservation protocol can be used when excessive collisions are experienced or expected (RequestToSend/ClearToSend used for Collision Avoidance or CA) in an attempt to try to avoid collisions.

A Wi-Fi network can be used to connect computers to each other to the internet and to wired networks (which use IEEE 802.3 or Ethernet). Wi-Fi networks operate in the unlicensed 2.4 (802.11b/g) and 5 GHz (802.11a/h) radio bands, with an 11 Mbit/s (802.11b) or 54 Mbit/s (802.11a or g) data rate or with products that contain both bands (dual band). They can provide real world performance similar to the basic 10BaseT wired Ethernet networks.